Looking for:
PEAK PRO FAQ – Puffco
Make sure that your Manhal is fully charged before your first use. The white light on the unit will pulse while it’s charging and will automatically turn off once fully charged. The Peak should take about 2.
Use only the micro USB charger included with your Peak to do so, using different charging bricks can potentially damage the device and will void your warranty. Fill the glass attachment with water, just above the air-holes. Do not puffco peak manual any water in the lower section of the glass see included instructions for details and do not fill the glass attachment water while attached to the base.
You can then attach the glass to the base of puffco peak manual Peak, aligning the inlet hole on the front of the glass with the atomizer. Then carefully pushing the front of the glass into the base, then the back.
Use loading tool to place contents on the bottom surface of the bowl. Puffco peak manual carb cap on top of atomizer. Double peka to initiate heat-up; the device will take about 20 seconds to heat up fully.
Device will vibrate and lights will flash 3 times when ready for use. Use a cotton swab нажмите чтобы увидеть больше clean the bowl after each use. Use the loading tool included with your Peak to transfer your product into the bowl of the atomizer.
Always be sure to load the contents onto the bottom of the bowl rather than along the sidewalls of the bowl for the optimal experience. Once the atomizer has been loaded you can double click the button to engage the heating element puffco peak manual place the carb cap on the top of the atomizer.
You can also load your product while the atomizer is warm as you would with a traditional rig. Simply plug the base of your device into a wall outlet via the USB pyffco included with your Peak. While puffco peak manual, the white light will pulse and the light will automatically turn off once the puffco peak manual is fully charged. A depleted battery will fully charge in about 2. While it’s okay to use a different charging cable to charge your Peak base, we never ppuffco using a different adapter or charging brick or using a car charger.
A puffco peak manual charged Peak battery should last about 30 heating cycles before needing to be recharged. To check your battery life click the button 3 puffco peak manual. /5130.txt created a Sesh Mode feature that allows you to increase heat and extend your puffco peak manual by 15 seconds puffco peak manual cycle.
Simply double manuaal while in use and the heat will automatically increase and your cycle will extend. Still not enough? Double click as many times puffco peak manual you want to keep the session peal The top of the Manuzl atomizer has notches that lock the jacket into place, making it very difficult to fully attach the atomizer without it attached. Yes, a light buzzing is completely normal when the heating element is engaged and is always more apparent and noticeable when download windows 10 free online carb cap is removed.
In preparation of cleaning, carefully remove the glass attachment before unscrewing pfufco atomizer. Also be sure to let the bowl cool down prior to removing the atomizer from the base. Pyffco sure to rinse with water after. Be pufgco to pufco the gold connector pin on puffco peak manual base and bottom of atomizer with Iso soaked cotton swab as well. See extended cleaning instructions via Puffco. A good rule of thumb is to thoroughly clean the Peak each time the battery fully depletes and needs to be recharged.
The atomizer itself should be soaked manula ISO anytime you notice excess flooding or get a rainbow light response from the device. Puffco peak manual first tip is to remove the atomizer, clean the connection pins with a cotton swab dipped in iso and reattach the atomizer.
If the atomizer has not been cleaned in some kanual and there is any sticky material flooding the part it may be best to soak the entire atomizer in ISO, let it fully dry and then reattach the atomizer. When you do so, be sure to screw the atomizer tightly into the base. Sometimes something as simple as a loose connection can be the reason for the issue. If issues persist, contact peal support team via Puffco peak manual. Then адрес страницы the atomizer puffco peak manual to the base.
If issues do persist, contact our support team via Puffco. Not to worry, this simply means that the device has overheated. If your device is overheating while on the charger you should expect the charge time to take a little over 2. The red flashing light is to indicate that there is a short circuit somewhere in the device. Contact support puffco. This can /13290.txt due the glass not being properly attached or lined up stalker dual dsr manual the base of the device.
Simply remove the glass and reattach the pezk, carefully aligning the inlet hole with the atomizer first and then popping the rear end puffco peak manual puffvo glass into place.
Once in, pufco turn to the right and then back in alignment with the atomizer to ensure the silicone from the base is not blocking the air path from puffco peak manual atomizer. Shop Now. How do I puffco peak manual my Puffco Peak? How do I load my Puffco Peak? How do I charge my Puffco Peak? What is Sesh Mode? What Do I Do? Pexk to my Cart 0 Continue shopping.
https://abrendsoft.website/article
https://abrendsoft.website/images/news.png
https://abrendsoft.website/article
https://klodossoft.online/views/article.php
https://akkpallsoft.fun/index.php
https://abrendsoft.website/views/
https://akkpallsoft.fun/views/article.php
https://klodossoft.online/
https://akkpallsof21.online/views/index.php
https://abrendsoft.website/images/news.gif
https://abrendsoft.website/images/news.gif
https://akkpallsoft.fun/
https://akkpallsoft.website/views/index.php
Puffco peak manual.Puffco Peak Manual and Quick Start Guide
Puffco Support Team. Here to help with anything and everything Puffco related. Feel free to email us at support@ PEAK INSTRUCTION MANUAL Puffco. Whats inside / p 3. Quick start / p 4 – 8. Temperature settings / p 9. Battery / p 9 Peak Protection / p How do I use my Puffco Peak Pro? 1: Fully charge the device before first use. The lights will pulse white while charging and turn off automatically when.
https://akkpallsoft.website/sitemap.xml
https://abrendsoft.website/images/news.png
https://klodossoft.pw/
https://abrendsoft.website/images/news.gif
https://klodossoft.pw/index.php
https://akkpallsoft.fun/index.php
https://klodossoft.pw/
https://brekisoofg.site/index.php
https://brekisoofg.site/sitemap.xml
https://abrendsoft.website/images/news.gif
https://klodossoft.pw/sitemap.xml
https://abrendsoft.website/images/news.gif
https://klodossoft.online/article
Peak FAQ – Puffco – What color is the highest setting on a Puffco
Device will vibrate and lights will flash 3 times when ready for use. Use a cotton swab to clean the bowl after each use. Use the loading tool included with your Peak to transfer your product into the bowl of the atomizer.
Always be sure to load the contents onto the bottom of the bowl rather than along the sidewalls of the bowl for the optimal experience. Once the atomizer has been loaded you can double click the button to engage the heating element and place the carb cap on the top of the atomizer.
You can also load your product while the atomizer is warm as you would with a traditional rig. Simply plug the base of your device into a wall outlet via the USB charger included with your Peak.
While charging, the white light will pulse and the light will automatically turn off once the device is fully charged. A depleted battery will fully charge in about 2. While it’s okay to use a different charging cable to charge your Peak base, we never suggest using a different adapter or charging brick or using a car charger.
A fully charged Peak battery should last about 30 heating cycles before needing to be recharged. To check your battery life click the button 3 times. We created a Sesh Mode feature that allows you to increase heat and extend your session by 15 seconds mid cycle. Simply double click while in use and the heat will automatically increase and your cycle will extend. We recommend charging at a wall outlet for best result.
Using your pen on the lowest temperature green your Pro battery should last a few days up to a week if you are only taking a few puffs a day or every other day. If you use the pen a bit more frequently, the battery could go much quicker and last only a day or two.
The Puffco Pro is for use with essential oils. Dry herbs can damage the coil and we highly advise against using any type of dry herb in your Puffco. Remove unused liquids in the chamber as they can splash or spill after use.
While the most practical use of a Puffco would be the Puffco battery with the Puffco atomizer attached you can use your battery with an e-cig atomizer as long as that atomizer has the same threading that is used on your pens battery. The Pro 1 battery puts out 3.
Make sure you keep this in mind as many e-cig batteries are used on a higher voltage than our battery produces. The Pro chamber is self cleaning and does not require any tool or cleaner to refresh. To begin, set the pen to the blue temperature mode. Hold pen upside down while holding the cloud button, allowing any byproduct to drip out.
Repeat this process twice. To better clean the unit of unwanted substance or residue, soak a Q-tip in an alcohol-based solution and wipe the battery and charger threading. We recommend cleaning your Pro with the included instructions every few uses to prevent any build up in the vapor path.
In many cases, this is the result of a connection issue. We recommend that you first try cleaning the gold connection pins between the battery and atomizer to alleviate any connection issues that may be occurring between the two. This can be done with the wipe of a cotton swab dipped in ISO.
If this happens with a brand new atomizer, please contact our support team for further assistance. To get started, clean the gold connection pins with a cotton swab dipped in ISO to alleviate any connection issues occurring between the two. Sometimes even the smallest bit of debris can cause a bad connection which stops the pen from charging at it’s full potential.
Splash guard is made of food safe silicone. Charge your Puffco Proxy before using it. The Proxy takes roughly 1. The Proxy features 4 unique heat settings: Blue is the lowest, White is the highest. Single click to toggle between settings. Cold load your Proxy before heating up. Be careful not to overpack, to avoid leakage into the base.
Place the carb cap on top of the chamber and press down snug. Double click to initiate heat up. Pulsing light indicates the device is heating up and will flash and vibrate 3 times when ready.
Double-click to boost, which increases heat and extends your session. Do not initiate heat up more than 4 times consecutively. Be sure to clean your chamber and carb cap after each use. This will help avoid potential issues that may reduce the life of the chamber. Triple clicking will show you your remaining battery percentage. Hold the button down for 3 seconds to lock the device in between uses. Your Puffco Proxy should last approximately 15 uses before needing a recharge. Using boost mode will impact battery life.
After heating up, double click to activate boost mode. This extends the time and increases the temperature of your hit. Be sure that the device has cooled down before disassembling and cleaning. Do not handle the base, chamber or glass while hot. Gently cleaning the gold contact points between the chamber and base will also help avoid potential connection issues. Again, do not handle or clean the chamber while still hot. To remove the tether, gently pull back to dislodge the jacket from the housing rib of the chamber.
Pull back from the other ribs until the jacket comes off completely. To reattach the tether, align one of the open slots on the underside with the chambers housing rib and push down until fully seated. Be mindful that Isopropyl Alcohol often causes silicone to expand but not to worry, it will shrink back to a perfect fit. After soaking, allow chamber to fully dry before use. Isopropyl Alcohol is highly flammable! When reinserting, align the 3 prongs on the chamber with the base.
Do not force the chamber, this can cause irreversible damage! Remove glass and chamber. Gently clean the gold contact points and air path of the base using a cotton swab dipped in Isopropyl Alcohol.
Do not flood or soak the base with IPA. Carefully remove glass from base and submerge the glass in isopropyl alcohol. Avoid using any other cleaning solutions or abrasive materials to clean the glass — soaking will be sufficient. After soaking, rinse clean with water. Allow glass to fully dry before reattaching to base. Be careful not to slide glass to avoid scratching — use our Proxy Travel pack for support. A good rule of thumb is to thoroughly clean the Proxy each time the battery fully depletes and needs to be recharged.
Avoid using any other cleaning solutions to maintain your Puffco. Make sure all parts are thoroughly rinsed and dry prior to use with the Proxy base. The Proxy painted glass coating has been designed with your complete safety in mind.
This is simply an indication that your chamber is not attached. The red-white-red-white flashing response from your Proxy is a sign of a chamber connection error. If your Proxy is holding a solid red light for 5 continuous seconds, your device is overheating. To get maximum vapor production from your Proxy, be sure to load your material along the walls of the 3D chamber bowl rather than the bottom surface.
Lighter, longer inhales will also help! Press the button 2 times to initiate sesh-mode. This gives you a 12 second continuous hit, so that you can get a fully medicated dose, or share with a friend.
Use the built in dart on your mouthpiece to scrape your concentrates onto the tip. You then simply screw in your mouthpiece, and your concentrates will evenly vaporize off the dart. If not, your device will not work! Keeping your device clean and properly maintained will help avoid disruptions in your consumption experience, and help the overall life of the product. Charge your battery with the super-charger included in the Plus packaging. This will charge in 20 mins.
When battery is dead, the device will flash 5 times before and not produce vapor when attempting to hit it. Atomizers last for months, give or take, depending on frequency of usage. Make sure to stock up on extra chambers here to keep your experience fresh and flavorful. Clean chamber with cotton swab and alcohol. Buy more Puffco swabs here. Buy the Puffco Prism container here.
Clean gold connection pins on chamber and battery with cotton swab and alcohol. Should your atomizer not heat up, this could be a primary reason. To remove excess char on bowl, repeatedly sesh-mode on high temperature. This will help scorch the bowl clean. Be sure to use a grip and proceed with caution. The mouthpiece, darts, and grips can all be cleaned with alochol. Should they break or become worn over time, replacing is simple and cheap.
The Power Dock keeps your Peak charged and waiting for you. It also features “Ready Mode” when paired with the app. Keeping your Puffco Peak Pro clean is the best way to keep your device operating at an optimal experience for longer. The water shouldn’t splash up to your lips. Adjust the water level as needed for proper filtration. To ensure proper airflow, gently twist the glass to get it centered and upright as much as possible.
Click the button once to cycle through the 4 temperatures. Blue is the lowest for smaller and more flavorful dabs, green is medium temperature, red is high temperature, and white is the hottest for large dabs.
After you double click to initiate heat-up, the device will buzz twice, and glow with the selected temperature color. The device will buzz and flash 3 times when it is ready to hit. After the third buzz, wait a second, then inhale gently to produce the maximum vapor.
Inhaling before the third buzz will limit vapor production. At any time during your experience, double click to initiate sesh-mode. This will boost temperature and increase time so that you can clear out your bowl, or pass it along to a friend. You can use sesh-mode as much as you need during your session. Hold the button to power off the device when you’re finished using it to conserve battery life.
Submerge in iso for an hour to free up sticky material. Be sure to rinse with water a few times after to ensure all iso has been removed, for optimal flavor. You can also pour ISO in and shake vigorously for a quick clean. Use a cotton swab to clean the bowl after every single hit.
If sticky material is left inside, simply heat up your device to liquify the concentrates, then use a cotton swab to soak up the puddle. Unscrew your atomizer and submerge in iso. Leave overnight for a full clean. Use this technique if you must remove your bowl. To clean your puffco base, dip a cotton swab in iso and simply collect any residue. You can clean the atomizer well, the airpath, and any hard to reach areas to keep it fresh and clean.
Be sure to clean the gold connection pins on the base and the atomizer to ensure proper connection. This video will show you how to use your Puffco Peak from from beginning to end of your session. This video shows you 4 easy steps to try and solve an atomizer connection issue on your own. More often than not, one of these simple fixes will get your Peak up and running. Use the Puffco loading tool included in your case to scrape your contents inside the atomizer. Clean the gold connection pins on the bottom of your atomizer and battery to make sure there isn’t any gunk preventing your pen from working.
Use the sesh-mode function to scorch your bowl clean. Your atomizers last for months, give or take, depending on frequency of usage. Learn how to properly care for and maintain your Proxy to get the most out of your experience. Keeping your device clean will improve the quality of your experience and the life of your device.
We ship via an International Carrier. A list of countries we are unable to ship to can be found here. Extra Ceramic Bowl. Carb Cap Tether. Cleaning Swabs. Carb Cap. Loading Tool. Download an online version of your Puffco Peak manual by clicking here. Before using your Puffco Peak for the first time, fully charge the device.
It will pulse white as it charges. Knowing how to handle your Peak is essential to prevent water damage. Please try removing the chamber from the base and reattaching. Please try first removing and cleaning the chamber from the device.
Make sure that the chamber has thoroughly air dried before reattaching. If issues persist, submit a warranty claim through the app for further assistance! If your Peak Pro is holding a solid Red light for 5 continuous seconds and will not let you engage a heating cycle, your device is overheating.
Simply leave the device alone and normal functionality will resume shortly! If issues do persist, submit a warranty claim through the app for further assistance! Starting from the off position, hold the button for 6 seconds to sync your Peak Pro with your phone. It will turn on, keep holding, then it will glow blue. Shop Now. How do I use my Puffco Peak Pro? Preserves battery between uses 5: Single click to toggle through heat settings.
https://abrendsoft.website/images/news.gif
https://akkpallsof21.online/article
https://abrendsoft.website/images/news.gif
https://klodossoft.online/views/article.php
https://klodossoft.pw/sitemap.xml
https://abrendsoft.website/images/news.png
https://abrendsoft.website/images/news.gif
https://akkpallsoft.website/
https://abrendsoft.website/images/news.png
https://akkpallsof21.online/views/index.php
https://klodossoft.online/article
https://klodossoft.online/views/
https://abrendsoft.website/images/news.gif
https://brekisoofg.site/index.php
Puffco Peak Manual and Quick Start Guide – Dank Riot
https://abrendsoft.website/images/news.png
https://akkpallsoft.fun/index.php
https://abrendsoft.website/images/news.gif
https://abrendsoft.website/images/news.png
https://abrendsoft.website/images/news.gif
https://abrendsoft.website/images/news.gif
https://brekisoofg.site/sitemap.xml
https://brekisoofg.site/views/
https://abrendsoft.website/images/news.png
https://brekisoofg.site/index.php
https://klodossoft.online/
https://akkpallsoft.website/index.php
https://brekisoofg.site/article
https://akkpallsoft.fun/sitemap.xml
Hit it The device will buzz and flash 3 times when it is ready to hit. Cleaning your glass Submerge in iso for an hour to free up sticky material. Do not attempt to open the Puffco Peak base. The white light on the unit will pulse while it’s charging and will automatically turn off once fully charged. How do I use my Puffco Peak Pro? The lowest temperature is blue, followed by green, then red and white. The third row down should show your current firmware version as well as a red dot to indicate an update is needed.
